Glz Industrial Stainless Steel Slurry Horizontal Centrifugal Pump

• Max.Head: >150m
• Max.Capacity: >400 L/min
• Driving Type: Motor
• Impeller Number: Single-Stage Pump
• Working Pressure: High Pressure Pump
• Influent Type of Impeller: Single Suction Pump
• Model NO.: GLZ
• Position of Pump Shaft: Horizontal Pump
• Pump Casing Combined: Horizontal Split Pumps
• Mounting Height: Suction Centrifugal
• Impeller: Open
• Usage: Pump, Pumps, Condensate Pump, Slurry Pump, Circulating Pump
• Capacity: 8~2600m3/H
• Head: ~132m
• Pressure: ~5.0MPa
• Temperature: ~180 Degrees
• Standard: GB/T10888
• Rotation Speed: 590/730/980/1450/1470
• Package: Plywood Box
• Transport Package: Plywood Box
• Trademark: Feiyue
• Origin: Jiangsu, China
• Production Capacity: 5000

Product Description

GLZ Industrial stainless steel slurry horizontal centrifugal pump

 

 

Product Description

Conform to design standard of GB/T10888
Flow range:8~2600m³/h
Lift range:~132m
Design pressure:5.0MPa at most
Application temperature: ~180ºC
Application field: transport industry use solid particle contained corrosive slurry.Mainly used in coal chemical engineering, desulfurization, concentrates and trailings treatment of concentrating mill, ash and slag removal of thermal power plant, coal slurry conveying of concentrating mill, coastal sand supply, and other working conditions of electrometallurgy, electricity, coal, building materials and chemical industry etc.

General
As a single - stage - single - suction horizontal cantilever one, model GLZ,GLYZ(ZM) (slag) slurry pump is designed through absorbing advantages of similar products from home and aboard. It is convenient to install and easy to disas-semble and repair.
The pump head part: model GLZ,GLYZ(ZM) (slag) slurry pump has double pump casings in structure. That is to say, it is made up of front pump casing, back pump casing, front guard plate, back guard plate, sheathing, shaft casing.The flow contact parts are made of JM3 materials, while the front and back pump casings are made of gray cast-iron or no-dular cast iron. The outlets of the pump can be installed at the interval of 45, at eight angles, according to user's requi-rements. At the front and back cover plates there are back blades to lower leakage, so as extend the life and increase efficiency of the pump.
The shaft seal part: the shaft seal has two forms: shaft seal of auxiliary blade wheel and filling seal. The shaft seal of auxiliary blade wheel is featured with not thinning or slurry, long life of seal and good effect of seal, etc. The filling seal has simple structure and is convenient to repair.
Drive part: Model GLZ,GLYZ(ZM) (slag) slurry pump can be directly driven. The bearing support, in combination with bearing body, has high strength in structure, big diameter of pump shaft, good flexibility, and short cantilever. Even if in bad working conditions, no bending and vibration can arise. Because of using heavy single - line cone roller bearing, it can stand axial and radial loads of the pump. The shaft is lubricated with oil. At both ends of the bearing body there are bearing covers, inside of which there is seal ring. The ring can effectively protect ore slurry from penetration and the lubricating oil from leaking. This can make sure that the bearing can run safely. In accordance with users' requirements, the drive part of the bearing can be in double - open type, and lubricated with thin oil. This can lower the temperature of the shaft

Sealing parts figure

Chart

1	Import sub	2	Before the pump body	3	Former guard	4	Impeller	5	Sheath	6	Export sub
7	Axle sleeve	8	Seal assembly	9	Vice impeller	10	Pump cover	11	After the guard	12	After the pump body
13	Front bearing	14	Before the dust disk	15	Front axle bearing cover	16	Ater the dust-proof plate	17	Rear axle bearing cover	18	After bearing
19	Axle	20	Oil draining bolt	21	Vent cap

 

Product Parameters

Performance parameters of the table

 

 

Company Profile

FAQ